Need help choosing an antenna? Need to design a custom antenna? WE CAN HELP: techsupport@arcadianinc.com

Arcadian Blog — Cables

Crimping Tools Needed to Replace Mobile Radios

Posted by Michael Crudele on

 Recently a client reached out to us about replacing a few of the antennas for their mobile radios with base station configurations.

Continue Reading...

Read more →

Cellular Antenna to be mounted at Side of Building with 25 foot Extension Cables

Posted by Michael Crudele on

We recently had a client reach out to us about a cellular antenna that he wanted to place on the side of his building. He noticed that we had a vehicular antenna, part 170653-000, and wanted something similar to that product. He also informed us that he was looking for a 25-foot cable extension and wanted to receive some recommendations.   Considering part # 170653-000 is a dual cellular product and our assumption that your main concern is to have an antenna outside, we recommend 2 pcs of the Cradlepoint outdoor omnidirectional antenna # 170668-000. Part # 170668-000 is a...

Read more →

Advantages and Disadvantages of PT195, PT240, and PT400

Posted by Michael Crudele on

  Advantages Disadvantages PT195: Recommended for use with frequencies under 900 MHz Lower loss than standard RG58 cable The most flexible   Less flexible than the RG58 Too much attenuation/ loss for frequencies over 900 MHz Don’t recommend using cable lengths over 15-20 ft. at 900 MHz PT240: Recommended for use with frequencies from 150 MHz – 5 GHz   Much lower loss and higher performance than standard RG58 and PT195 cable Flexible Excellent for UHF RFID Much less flexible than RG58 and PT195 Too much attenuation/ loss for frequencies over 900 MHz at lengths of 50+ ft. PT400: Recommended...

Read more →

Connectors and Wiring for Custom Cradlepoint Cables

Posted by Michael Crudele on

A client reached out to us asking if we sell the connectors and wiring to make custom cables for Cradlepoint’s 170668-000 Multi-Band Antenna. I let him know that I’d be able to push him in the right direction with the following suggestions…   Please note that you would only need one of these cables:   PT240-010-SNM-SSM: 10 ft. long, LMR240 type cable with standard N-male & standard SMA-male connectors PT240-025-SNM-SSM: 25 ft. long, LMR240 type cable with standard N-male & standard SMA-male connectors PT400-050-SNM-SSM: 50 ft. long, LMR400 type cable with standard N-male & standard SMA-male connectors   Click here...

Read more →

Extension to a 10 Foot Cable

Posted by Michael Crudele on

Q) I recently purchased part # S8658PL96RTN but need a 25 ft. cable. Unfortunately, this part # comes with a 10 ft. cable so it’s not long enough. Is there any way I can purchase this part but with a 25 ft. cable?   A) The part purchased has a 96 inch /8-foot long cable with an RPTNC-male connector. Unfortunately, we do not carry this part with a 25 ft. cable, so you’d have to purchase a cable extension. Below you will find a few suggestions…   PT195-018-RTF-RTM: LMR195 cable, 18 ft. long with RPTNC-Female & RPTNC-Male connectors. PT195-015-RTF-RTM: LMR195...

Read more →

Accessories to Use to Mount Part # TRA6927M3NB-001 on a Stainless Box

Posted by Michael Crudele on

In the past, we’ve had a client express his interests in our mounting accessories for part # TRA6927M3NB-001. He wanted to be able to post the antenna to a stainless box and wanted our suggestions regarding the issue. Do we have something to alleviate this problem? Yes, we do!   We have an adapter for the part # TRA6972M3-NB-001 by the part # VTPM800 (not MTPM800). Part # VTPM800 is a Laird/ Antenex ¾ inch NMO to 5/8 in N-female coax adapter. It is used when mounting to surfaces up to 1 inch thick.     However, if you would like to use a...

Read more →